MASTER-RING gyűrűs térelzárás Ø 80 mm
Ø 48-50 mm-es csövekhez

cikkszám 120095

MASTER-RING tömítőbetétek

Víznyomás teszt Radontight

Medium pipe outer Ø 48 up to 50 mm

for core drill hole and lining pipe stainless steel V2 A - Test MPA

Hozzáadás a hirdetési listához

A legfontosabb információk egy pillantásra

switch_to_language DE
switch_to_language GB
switch_to_language FR
switch_to_language NL
switch_to_language IT
switch_to_language ES
switch_to_language CZ
switch_to_language PL
switch_to_language RO
switch_to_language DK
switch_to_language SE
switch_to_language NO
switch_to_language FI
switch_to_language RS
switch_to_language RU
switch_to_language GR
switch_to_language TR

Tovább a Youtube-ra

start Animáció
cikkszám:
120095
cikkcsoport:
440 - RRD
GTIN:
4251689528590
vámtarifaszám:
84842000
csomagolóegység:
pc
értékesítési mennyiség egység:
1 Stk
súly per:
pc = 0.4 kg
anyag:

A tömítőelem: Környezetbarát EPDM gumi
Tömítés szélessége: 40mm

Nyomólapok, csavarok, anyák: V2A

szín:
Gumi elem: fekete
Nyomtatólemezek: ezüstös
Csavarok:

M6-os hatszögletű foglalat

Szélesség a lakásokon keresztül:

Hexagon 5 mm

maximális nyomaték:

5 Nm (mérettartó csövek)

termikus alkalmazási terület:
kb. -30° C-tól 120° C-ig
víznyomósság:
3,0 bar-ig (helyzeti biztonsági berendezés nélkül)
5,0 bar-ig (helymegoldással, a helyszínen)
tárolás:
Száraz, közvetlen napfénytől védett helyen tárolandó
ártalmatlanítás:
Háztartási hulladéklerakókban a helyi hulladékkezelési előírásoknak megfelelően ártalmatlanítható.

Supply takes place completely ready to be installed.
The MASTER-RING gasket insert consists of two pressure plates, a rubber part and the appropriate screws and nuts.
The pressure plates, the screws and the nuts are made of V2A stainless steel.


Before installation the MASTER-RING gasket insert, the inside of the core drill hole and the outside of the gas, water, sewage pipes as well as the cables have to be cleaned.


When installing a MASTER-RING gasket insert in a core drill hole the inside of the core drill hole has to be preserved with an epoxy resin ( PROTECT EP resin).
The preservation serves to obtain a smooth surface and secondly as protection of the cut reinforcement steels against corrosion.


Insert the MASTER-RING gasket insert into the lining pipe or the perserved core drill hole and push the pipe/cable through.
The MASTER-RING gasket insert must be installed as close as possible to the outside of the wall ( earth-side, water-side).
Take care that the nuts can be controlled and retightened later.
The nuts have to be placed on the air-side.


Tighten the screws crosswise through one turn.
Repeat this process until all screws are tightened to the specified max. torque.
This procedure guarantees uniform pressing out of the rubber against the inside of the lining pipe / core drill hole.
Check the torque after 1-2 hours and retighten the screws if necessary.

Status: 23.03.2022


Master Ring in Lining-Pipe in precast-wall

DWG letöltése

PDF letöltése

Master Ring in core-drill hole in precast wall

DWG letöltése

PDF letöltése

Master Ring in Lining-Pipe in in-situ concrete

DWG letöltése

PDF letöltése

Master Ring in core-drill hole in in-situ concrete

DWG letöltése

PDF letöltése

Tartozékok

megfelelő tartozékok

MC-Injekt 1264 kompakt (epoxigyanta)

Epoxigyanta az erősen illeszkedő tömítésekhez. Epoxigyanta repedések, hézagok és üregek nem pozitív kitöltésére építési, mélyépít...

Kapcsolatfelvétel

Szívesen válaszolunk kérdéseire

Kérjük, adja meg a nevét
kérjük, adja meg a vállalatot
kérjük, adja meg a várost
Kérjük, adja meg e-mail címét
Kérjük, adja meg a tárgyat
Kérjük, írja be az üzenetet

Kérjük, töltse ki a következő captcha-t a spam csökkentése érdekében.

Kérjük, írja be a captcha-t.

Nem léphetünk kapcsolatba Önnel, ha nem ért egyet az adatvédelmi nyilatkozatunkkal.