från natriumbentonit
artikelnummer 010020
Produktbeskrivning
.
MASTERSTOP bentonitsvällande tejper har testats i byggbranschen i åratal, sväller vid kontakt med vatten och tätar sprickor eller konstruktionsfogar på ett säkert och permanent sätt.
.
Testerna säkerställer att produkten är lämplig för de olika användningsområdena.
- Enkel och säker installation
- Inga gjutna delar och svetsar
- Inga uppresningar
- Svällnings- och krympningsprocessen är reversibel
- Självinsprutande effekt Dimensionsstabil och icke-klibbig
- De svällande tejperna tränger in i sprickor och håligheter
- Inget avfall eller restbitar
- Miljövänlig
- Säkra tack vare omfattande tester
Den viktigaste informationen i en överblick
Natriumbentonit med gummiinnehåll
Smidig
Plastik
20 x 15 mm
.Upp till 340 % i normalt vatten (pH 7)
.
upp till 160 % i vätskor som kraftigt angriper betong
upp till 140 % i alkaliska vätskor
upp till 140 % i alkaliska vätskor
Nej
Ja
Nej
Ja
Generellt provningscertifikat från byggnadsmyndigheten (abP)
MFPA Leipzig
.
Nr: P-SAC 02 / 5.1 / 12-057
Europeisk teknisk bedömning
ETA - 16 / 0735
och
daterad den 13 september 2017
Ja
Användningsklass A för lastklass 1 och 2 i enlighet med WU:s riktlinjer
Kan omhändertas i deponier eller förbränningsanläggningar i enlighet med lokala bestämmelser för avfallshantering.
Installation with swelling tape adhesive:
The substrate must be clean, dry, and free of loose particles.
Apply the swelling tape adhesive in the centre of the joint in a uniform bead (width 8-10 mm) out of the cartridge onto the surface.
The subsequent concrete covering must be at least 8 cm on all sides.
Once the swelling tape adhesive has been applied in the centre of the joint, the MASTERSTOP bentonite swelling tape is placed on the adhesive and gently pressed on, moving it slightly back and forth, crosswise to the longitudinal axis.
When the tape is fixed, the adhesive should slightly ooze out on both sides.
This guarantees a complete fixation.
Ready for use after 4 – 6 hours (depending on weather conditions)
Installation with swelling tape grid:
The substrate must be clean, dry, and free of loose particles.
Place the MASTERSTOP bentonite swelling tape in the centre of the joint.
The subsequent concrete covering should be at least 8 cm on all sides.
Position the swelling tape correctly.
Push the fixing grid firmly onto the MASTERSTOP bentonite swelling tape.
Fasten using corresponding nails and either by hand or mechanically using a bolt-firing tool.
The distance between nails must not exceed 20 cm in the longitudinal direction of the swelling tape.
Both, straight and angle joints need to be butt jointed.
The joint areas must be form-fit in order to avoid any discontinuity in the system.
In the case of butt joints in the straight line and the use of swelling tape grids, the joints of swelling tape and swelling tape grid should be offset.
Status: 23.03.2022
Tillbehör
lämpliga tillbehör
Enkomponents, lösningsmedelsfri fogmassa för limning av MASTERSTOP bentonitsvällande tejper. Förbrukning: 40 - 50 ml/m ...
Liknande produkter
Du hittar liknande produkter här.
Detta är ett test...
Kontakta oss
Vi svarar gärna på dina frågor