ορυκτό, πλήρως επικαλυμμένο και στις δύο πλευρές
αριθμός άρθρου 070481
Η σφράγιση των αρμών κατασκευής σκυροδέματος θέτει υψηλές απαιτήσεις στην τεχνολογία σφράγισης.
Πλήρως επικαλυμμένο με μια ειδική ορυκτή επίστρωση, το φύλλο στεγανοποίησης MB Overlap σε μορφή λωρίδας διασφαλίζει ότι οι αρμοί κατασκευών από σκυρόδεμα σφραγίζονται με ασφάλεια και μόνιμα από πιεστικό και μη πιεστικό νερό.
Η χρονοβόρα αφαίρεση της προστατευτικής μεμβράνης δεν είναι πλέον απαραίτητη.
Προσθήκη στη λίστα ειδοποιήσεωνΟι πιο σημαντικές πληροφορίες με μια ματιά
St 37, galvanized
special coating: mineral
σκληρό, τραχύ
2,4 m
160 mm
Περίπου 0,6 mm
Περίπου 0,2 mm
περίπου 1,0 mm
Πιστοποιητικό δοκιμής γενικής οικοδομικής αρχής (AbP)
MPA Braunschweig
JGS - έκθεση δοκιμής
MPA Braunschweig
(1200/549/17) - Pan
Ja
Κατηγορία χρήσης A για κατηγορίες φορτίου 1 και 2 σύμφωνα με την οδηγία WU
Ξύλινο κουτί (255 x 25 x 31 cm)
50 τεμάχια λωρίδες
55 τεμάχια σφιγκτήρες
για τη Γερμανία:
(στήλη νερού 10 m, λαμβάνεται υπόψη συντελεστής ασφαλείας 2,5 φορές).
![](/Einbauanleitungen/WG2/Dichtblech%20MB/20036/image-thumb__20036__textandimagecombi/MB,P20Verpackung.01d1205b.jpg.pagespeed.ce.wELkVepiic.jpg)
The product is delivered in a wooden crate.
The Joint sheet metal MB Overlap elements and the fixing clips are in the crate.
![](/Einbauanleitungen/WG2/Dichtblech%20MB/20037/image-thumb__20037__textandimagecombi/Bild%201.ac0c7d70.png)
Joint sheet metal MB Overlap elements are supplied ready to install.
A protective foil does not need to be removed.
Place the elements in the centre of the rising wall on top of the upper reinforcement layer.
Push the mounting brackets, 3 pcs/element, over the sheet metal and fix them to the upper reinforcement layer with binding wire.
The embedment depth in the concrete must be at least 3 cm and must not be more than half the height of the sheet metal (8 cm).
![](/Einbauanleitungen/WG2/Dichtblech%20MB/20038/image-thumb__20038__textandimagecombi/Bild,P202.9a5f5fe8.jpg.pagespeed.ce.d8ZCUWVq-f.jpg)
The joint of the Joint sheet metal MB Overlap can be made without glue, only by overlapping the two ends.
The length of the overlap must be at least 20 cm.
There must be no contamination on the surfaces that could interfere with bonding.
![](/Einbauanleitungen/WG2/Dichtblech%20MB/20039/image-thumb__20039__textandimagecombi/Bild,P203.5681be4e.jpg.pagespeed.ce.C20UEvH1lW.jpg)
The joint must be secured with one of the fixing clips provided.
Attention: The Joint sheet metal MB Overlap must not be plugged into the fresh concrete subsequently.
![](/Einbauanleitungen/WG2/Dichtblech%20MB/20040/image-thumb__20040__textandimagecombi/Bild,P204.e6af8041.jpg.pagespeed.ce.GfvJk9aDgO.jpg)
Corners can be formed by sharp-edged bending in-situ on the
building site.
![](/Einbauanleitungen/WG2/Dichtblech%20MB/20041/image-thumb__20041__textandimagecombi/Bild,P205.490f17f7.jpg.pagespeed.ce.-26Xe54i8p.jpg)
After some alignment the edge can be fixed on the reinforcement.
![](/Einbauanleitungen/WG2/Dichtblech%20MB/20042/image-thumb__20042__textandimagecombi/Bild,P206.72494731.jpg.pagespeed.ce.MR3p9up1c4.jpg)
To facilitate the fixing of the Joint sheet metal MB Overlap on the reinforcement start installation in a corner.
The placement of concrete in the area of the Joint sheet metal MB Overlap and corresponding preparations must be carried out in accordance with the established technical standards.
Status: 23.03.2022
Αξεσουάρ
κατάλληλα αξεσουάρ
Για τη στερέωση των αρμών επικάλυψης των επικαλυμμένων μεταλλικών υδατοφρακτών ...
Βαθμός στερέωσης για μεταλλικούς υδατοφράκτες ύψους έως 160 mm ...
Επικοινωνήστε μαζί μας
Θα χαρούμε να απαντήσουμε στις ερωτήσεις σας