avec technique de l'anneau en oignon - version divisée
numéro d'article 120222T
Aperçu des informations les plus importantes
Élément d'étanchéité : caoutchouc EPDM respectueux de l'environnement
.
Largeur du joint : 40 mm
Plaques de compression, vis, écrous : V2A
Plaques d'impression : argentées
M8
M8
M8
10 Nm (tubes de fluides indéformables)
Sans bouchon intérieur : 158 - 160 mm
1er anneau : 168 - 170 mm
2. Anneau : 178 - 180 mm
3. Anneau : 198 - 200 mm
3.
3e anneau : 198 - 200 mm
4e anneau : 208 - 210 mm
Sans le bouchon intérieur : 158 - 160 mm 4ème anneau : 208 - 210 mm
Constitution de l'anneau : 198 - 200 mm
4.
![](/Einbauanleitungen/WG4/MASTER-Ringe/MASTER-Ring%20Multi%20-%20geteilt/57829/image-thumb__57829__textandimagecombi/Zuschnitt.f5c130c1.png.pagespeed.ce.zHOsrNrj8A.png)
Adjust the sealing insert of the MASTER-Ring Multi split version to the diameter of the media line. To do this, push the required rings backwards through the seal.
![](/Einbauanleitungen/WG4/MASTER-Ringe/MASTER-Ring%20Multi%20-%20geteilt/57827/image-thumb__57827__textandimagecombi/B,PC3,PBCgel_ab.c8fd9d21.png.pagespeed.ce.xHeSD0E4RL.png)
Remove the locking clip of the MASTER-Ring Multi split version
![](/Einbauanleitungen/WG4/MASTER-Ringe/MASTER-Ring%20Multi%20-%20geteilt/57828/image-thumb__57828__textandimagecombi/,PC3,P96ffnen.7f11206e.png.pagespeed.ce.qYFXOJR8JZ.png)
Open the gasket on the side of the puzzle pieces.
![](/Einbauanleitungen/WG4/MASTER-Ringe/MASTER-Ring%20Multi%20-%20geteilt/57826/image-thumb__57826__textandimagecombi/Anbringen.188cfee8.png.pagespeed.ce.O6UsqYgTUo.png)
Place the MASTER-Ring Multi split version around the installed pipe.
![](/Einbauanleitungen/WG4/MASTER-Ringe/MASTER-Ring%20Multi%20-%20geteilt/57825/image-thumb__57825__textandimagecombi/Schlie,PC3,P9Fen.7a6f3038.png.pagespeed.ce.F8vp65aGvA.png)
Close the gasket and reinstall the locking clip and close it as well.
Push the seal into the annular gap.
![](/Einbauanleitungen/WG4/MASTER-Ringe/MASTER-Ring%20Multi%20-%20geteilt/57824/image-thumb__57824__textandimagecombi/Festziehen.e987d23b.png)
Tighten the screws crosswise through one turn.
![](/Einbauanleitungen/WG4/MASTER-Ringe/MASTER-Ring%20Multi%20-%20geteilt/57830/image-thumb__57830__textandimagecombi/Drehmoment.436ad101.png)
Tighten the screws to the specified max. torque. (Ø 100/150/200 = 5Nm; Ø250 = 10Nm).
Check the torque after 1-2 hours and retighten the screws if necessary.
Contactez nous
We are happy to answer your questions