iz natrijevega bentonita
številka izdelka 010012
MASTERSTOP "LONG TIME" bentonitni nabrekljivi trak za varno tesnjenje gradbenih stikov in prebojev v betonskih konstrukcijah pred vdorom vode. Vdor vode preprečujeta nabrekanje in nabrekalni tlak, ki nastane med nabrekanjem.
MASTERSTOP LONG TIME bentonitni nabrekljivi trak je tesnilo, ki lahko nabrekne v vodi. Sestavljen je iz fino zmletega glinenega minerala (natrijevega bentonita), ki je kot vezivo vgrajen v matrico iz nevulkanizirane gume. Za boljšo odpornost proti vremenskim vplivom je prevlečen s filmom, ki se sam raztopi v betonu. Dodaj na seznam obvestilNajpomembnejše informacije na prvi pogled
Natrijev bentonit
Gladko
plastik
Do 340 % v običajni vodi (PH 7)
do 150 % v tekočinah, ki močno napadajo beton
do 290 % v alkalnih tekočinah
Ne
Ja
Ne
Ja
ETA - 16 / 0735
Potrdilo o preskusu splošnega gradbenega organa (AbP), MFPA Leipzig
Št. dokumenta: P-SAC 02 / 5.1 / 15-253
približno 10 dni
izvede se približno 6-7 dni po betoniranju
Ja
Uporaba razreda A za razred obremenitve 1 in 2 v skladu s smernicami WU
![](/Einbauanleitungen/WG1/Masterstop%20LONGTIME/20001/image-thumb__20001__textandimagecombi/MASTERSTOP,P20LONG,P20TIME,P201.c76da511.jpg.pagespeed.ce.aGycQidwYV.jpg)
Since the MASTERSTOP "LONG TIME" is supplied with a protective sheating, the swelling tape can
only be fastened by using a special swelling tape grid.
The substrate must be clean, dry and free of loose parts.
Apply the MASTERSTOP "LONG TIME" in the middle of the joint to the concrete surface and fix it.
The later concrete cover must be at least 8cm.
The swelling tape must be bordered by reinforcement on both sides.
Minimum distance to the reinforcement: 5cm.
![© Mastertec GmbH & Co. KG © Mastertec GmbH & Co. KG](/Einbauanleitungen/WG1/Masterstop%20LONGTIME/1841/image-thumb__1841__textandimagecombi/Masterstop,P20Long,P20Time,P20Schnitt,P20ohne,P20Text,P20,P28PL2018,P20S.,P2014,P20oben,P20rechts,P29.454c7227.jpg.pagespeed.ce.uvWbuB2FVT.jpg)
Place the swelling tape grid carefully over the swelling tape without damaging the protective sheating.
The grid must only be nailed on through the side wings.
Fasten with suitable nails either by hand or mechanically with a bolt-firing tool.
![](/Einbauanleitungen/WG1/Masterstop%20LONGTIME/20000/image-thumb__20000__textandimagecombi/010012_Einbau,P204,P20,P28Longtime,P29.c3942e72.jpg.pagespeed.ce.3pQa0lxVCW.jpg)
The distance between nails should not exceed 25 cm in the longitudinal direction of the swelling tape.
At the beginning of the tape and if tape sections are used, pull back the protective sheating approx. 5 cm, cut off the swelling tape and fold over the extra length of sheating to prevent contact with water.
![](/Einbauanleitungen/WG1/Masterstop%20LONGTIME/19999/image-thumb__19999__textandimagecombi/010012_Einbau,P202,P20,P28Longtime,P29.a08e9c76.jpg.pagespeed.ce.NH1hkWVoTj.jpg)
In the corners, the swelling tape grid must be released in order to ensure a continuous firm fixation on the substrate.
In the case of butt joints in the straight line and the use of swelling tape grids, the joints of swelling tape and swelling tape grid should always be made in a staggered position.
Status: 23.03.2022
Dodatki
primerna dodatna oprema
Mreža za pas za MASTERSTOP "LONG TIME" 25/20, dolžina 1 m ...
Dolžina 42 mm z velikim diskom ...
Dolžina 40 mm z diskom ...
Pišite nam
Z veseljem bomo odgovorili na vaša vprašanja