STOPPER mini 22 (21,5-23 mm)

STOPPER mini 22 (21,5-23 mm)
Tahke plastikust tihendustopper

Artikli number 046150

STOPPER tihendid

Sisemine veekindlus plastist ja kiudtsemendist valmistatud seinte paksuse korral

Lisada märkuste loetellu

Kõige olulisem teave lühidalt

start Animatsioon

Tehnilised andmed

Artikli number:

046150

Artikligrupp:

610 - Stopper + Zubehör

GTIN:

4251689537912

tollitariifi number:

39259080

pakkimisüksus:

Ämber

müügikoguse ühik:

250 Stk

kaal ühe:

Ämber = 5 kg

materjal:

TPE - termoplastiline elastomeer

värv:

betoonhall

tihedus:

ca. 1,17 g/cm³

Kohaldamisala:

Sisese läbimõõdu jaoks 21,5 kuni 23 mm

Kõvadus:

ca. 70 ± 5 Shore A

Katsesertifikaat / load:

Testiaruanne
MFPA Leipzig
PB P 5.1/15-012

JGS test
MPA Braunschweig
(1200/442/15c) - Pan

Stabiilsus:

Et näiteks läga, vedelsõnnik, silo, metaanigaas, radoon, UV-kiirgus, osoon, bituumen

Välispakend:

250 tükki / ämber

Sisaldab aineid, mis on loetletud SVHC loetelus või mille osakaal on ≥0,1%.:

Toode vastab REACH-määrusele:

termiline rakendusala:

umbes -35°C kuni 70°C

veekindlus:

kuni 3 baari (30 m veesammas)

firebehavior:

Klass "B2", vastavalt DIN 4102 osa 1.

klass "E" vastavalt DIN-EN 13501-1.

ladustamine:

Säilitada kahjustamata ja avamata originaalpakendis kuivas kohas, eemal otsesest päikesevalgusest.

kõrvaldamine:

Võib kõrvaldada prügilates või põletusrajatistes vastavalt kohalikele jäätmekäitlusnormidele.

Andmed

Paigaldamise õpetus

Required tooling:
Hard rubber mallet: 1500 - 2000 g
Cleaning brush for tube 21.5 - 26 mm ( Art.-Nr.: 046170)
Drive-in aid ( Art.-Nr.: 046180)

Soiled distance tubes must be thoroughly cleaned before installing the STOPPER.
The entire installation area must be properly cleaned as otherwise it will not be possible to drive in the STOPPER to its final depth.

Whether using cones or lip seals, the STOPPER mini 22 can be used as the outer closure of the distance tube.

The STOPPER mini 22 is installed by driving it in with a hard rubber
mallet (weight 1500 - 2000 g) using reasonable force.

If a lip is used, the STOPPER mini 22 must be driven in so that it is flush.
The small surrounding edge of the STOPPER mini 22 must lie flat against the surface of the concrete.

!! The STOPPERS must always be driven in at both ends of the distance tubel!!

If used with a tapered cone, the last bit of the STOPPER mini 22 must be driven into position using a drive-in aid.

The STOPPER mini 22 is then driven in so far that the small surrounding edge is resting against the inner concrete surface.

!! The STOPPERS must always be driven in at both ends of the distance tubel!!

When driving in the second STOPPER mini 22 on the other end of the tube, it may appear that it is not possible to drive it in completely. This is due to compressed air trapped between the two STOPPERS.
If this situation occurs, simply wait and give the air time to escape before continuing to drive in the STOPPER into its final position.

Status: 23.03.2022

Lae alla paigaldamise juhendmaterjal

vastupanu tabel

DT-GB_Beständigkeiten_Stopper_06-2023.pdf

CAD-failid