Размери Ø приблизително 5/10 мм
номер на статията 030050
MASTERTUBE Системи от инжекционни маркучи
Уплътняването на бетонни строителни фуги поставя високи изисквания към технологията на уплътняване.
Инжекционният маркуч MASTERTUBE гарантира надеждно и трайно уплътняване на хоризонтални и вертикални бетонни строителни фуги срещу вода под налягане и без налягане. Добавяне към списъка с известияНай-важната информация с един поглед
Вътрешна тръба от PVC
Обвивка като моновлакнест плат
около 10 мм
приблизително 5 мм
Светъл, с функция на клапан
depending on injection agent,
approx. + 6°C to +40°C
Сертификат за изпитване на Общия строителен орган (AbP)
MFPA Лайпциг
No.: P-SAC 02 / 5.1 / 21 - 266-1 (PU смола)
No.: P-SAC 02 / 5.1 / 21 - 266-2 (акрилат)
До макс. 2 бара (20 м воден стълб)
Ja
Използвайте клас А за клас на натоварване 1 и 2 в съответствие с ръководството на WU
1 ролка за 100 м
.
![](/Einbauanleitungen/WG3/MASTERTUBE/20284/image-thumb__20284__textandimagecombi/Verpressschlauch_1.caebc070.jpg.pagespeed.ce._U7nsWBh5_.jpg)
The product is supplied on a 100 m reel.
Bind the hose with filament tape and use a suitably sharp tool to cut the hose to the required length.
Injection circuits must not exceed 8 m in length.
![](/Einbauanleitungen/WG3/MASTERTUBE/20286/image-thumb__20286__textandimagecombi/Verpressschlauch_2.af51dbbb.jpg.pagespeed.ce.jlKCLec5Wr.jpg)
After the hose has been cut to length, screw the respective connecting pieces fully into the hose (as far as they will go) - the image shows our fastening packers.
![](/Einbauanleitungen/WG3/MASTERTUBE/20285/image-thumb__20285__textandimagecombi/Verpressschlauch_3.1eceb5e8.jpg.pagespeed.ce.-2R0_Lpkcx.jpg)
Place the hose centrally in the construction joint, within the reinforcement.
The surface of the construction joint must be clean, level and free of burrs, defects and loose particles of dirt.
![](/Einbauanleitungen/WG3/MASTERTUBE/20287/image-thumb__20287__textandimagecombi/Verpressschlauch_4.c7298ddf.jpg.pagespeed.ce._TbLrKs0HH.jpg)
The hose can be fastened in place with metal clips for nailing (manual or nail gun).
The distance between the fastening clips must not exceed 15 cm.
![](/Einbauanleitungen/WG3/MASTERTUBE/20283/image-thumb__20283__textandimagecombi/Verpressschlauch_5.b7139c93.jpg.pagespeed.ce.-g_skGq3yv.jpg)
Alternatively, the hose can be fastened in place with plastic clips, either set in the fresh concrete or subsequently hammered into an 8 mm drill hole.
The distance between the fastening clips must not exceed 15 cm.
The hose must be in continuous contact with the concrete and must not be allowed to float.
![](/Einbauanleitungen/WG3/MASTERTUBE/54453/image-thumb__54453__textandimagecombi/2022-07-29_MASTERTUBE_Fuge_rau.ea3b6fc5.png)
Fixing on joints with category "rough"
On construction joints with a rough surface, fastening with a fastening grid is necessary to ensure full-surface support on the construction joint. The fixing grid is placed over the hose and fixed alternately (to the left and right of the hose) with nail plugs every 15 cm maximum.
![](/Einbauanleitungen/WG3/MASTERTUBE/20282/image-thumb__20282__textandimagecombi/Verpressschlauch_6.8f177e41.jpg.pagespeed.ce.pLgJpB0AwY.jpg)
Successive injection hose sections must overlap by at least 20 cm in order to ensure continuous injection of the joint.
![](/Einbauanleitungen/WG3/MASTERTUBE/20281/image-thumb__20281__textandimagecombi/Verpressschlauch_7.bdc674fc.jpg.pagespeed.ce.IMQnkCw58u.jpg)
All changes in direction must be implemented with a sufficiently wide bending radius in order not to damage the hose/restrict the overall injection flow.
The minimum radius is 5 cm.
The injection and ventilation ends can be kept in storage boxes, or alternatively the hose end can be attached to the formwork itself using fastening packers. The storage boxes or fastening packers must be arranged so they are easily accessible in the event of subsequent injection procedures (take high floor structures into consideration).
Once the concrete has cured, the resin can be injected via the fastening packers or the injection end pieces.
Status: 23.03.2022
HOSE CONNECTOR / VENTILATION HOSE / SEALING PLUG / STORAGE BOX in in-situ concrete
Изтегляне на DWG Изтегляне на PDFАксесоари
подходящи аксесоари
Закрепващият пакер MASTERTEC дава възможност инжекционният маркуч да бъде закрепен директно към кофража. Пакерът за закрепване по...
Закрепваща скоба за защитен от плаване монтаж на инжекционни маркучи върху бетонни повърхности ...
Полиуретанова смола за инжектиране на маркучи и пукнатини ...
Подобни продукти
Можете да намерите подобни продукти тук.
Уплътняването на бетонни строителни фуги поставя високи изисквания към технологията на уплътняване.Мастертръбата "ЖЪЛТА" г...
Свържете се с нас
Ще се радваме да отговорим на вашите въпроси