Cev za vbrizgavanje MASTERTUBE (rdeča/rumena)

Cev za vbrizgavanje MASTERTUBE (rdeča/rumena)
Dimenzija Ø približno 5/10 mm

številka izdelka 030050

MASTERTUBE Vbrizgalni cevni sistemi

Tesnjenje betonskih gradbenih stikov postavlja visoke zahteve glede tehnologije tesnjenja.

Injekcijska cev MASTERTUBE zagotavlja zanesljivo in trajno tesnjenje horizontalnih in vertikalnih betonskih gradbenih stikov pred tlačno in netlačno vodo. Dodaj na seznam obvestil

Najpomembnejše informacije na prvi pogled

Tehnični podatki

številka izdelka:

030050

skupina člankov:

300 - Injektionsschlauch

GTIN:

4251689514203

številka carinske tarife:

39172190

pakirna enota:

Roll

prodajna količina enota:

100 m

teža na:

Roll = 10 kg

material:

PVC notranja cev
Obloga kot monofilamentna tkanina

barva:

rot / gelb

Zunanji premer:

ca. 10 mm

Notranji premer:

približno 5 mm

Izhodne odprtine:

Svetloba, s funkcijo ventila

Temperatura uporabe:

depending on injection agent,
approx. + 6°C to +40°C

Potrdilo o preskusu / pooblastila:

Potrdilo o preskusu splošnega gradbenega organa (AbP)
MFPA Leipzig
Številka: P-SAC 02 / 5.1 / 21 - 266-1 (PU smola)
Številka: P-SAC 02 / 5.1 / 21 - 266-2 (akrilat)

Tesnost vodnega tlaka:

Do največ 2 bara (20 m vodnega stolpca)

Primerne cone za menjavo vode:

Ustreza:

Uporaba razreda A za razred obremenitve 1 in 2 v skladu s smernicami WU

Pakiranje:

1 rolka na 100 m

shranjevanje:

Shranjujte v nepoškodovani in neodprti originalni embalaži na suhem mestu, stran od neposredne sončne svetlobe.

odstranjevanje:

Lahko se odstrani na odlagališčih gospodinjskih odpadkov v skladu z lokalnimi predpisi o odstranjevanju odpadkov.

Podatkovni list

Navodila za namestitev

The product is supplied on a 100 m reel.
Bind the hose with filament tape and use a suitably sharp tool to cut the hose to the required length.
Injection circuits must not exceed 8 m in length.

After the hose has been cut to length, screw the respective connecting pieces fully into the hose (as far as they will go) - the image shows our fastening packers.

Place the hose centrally in the construction joint, within the reinforcement.
The surface of the construction joint must be clean, level and free of burrs, defects and loose particles of dirt.

The hose can be fastened in place with metal clips for nailing (manual or nail gun).
The distance between the fastening clips must not exceed 15 cm.

Alternatively, the hose can be fastened in place with plastic clips, either set in the fresh concrete or subsequently hammered into an 8 mm drill hole.
The distance between the fastening clips must not exceed 15 cm.
The hose must be in continuous contact with the concrete and must not be allowed to float.

Fixing on joints with category "rough"

On construction joints with a rough surface, fastening with a fastening grid is necessary to ensure full-surface support on the construction joint. The fixing grid is placed over the hose and fixed alternately (to the left and right of the hose) with nail plugs every 15 cm maximum.

Successive injection hose sections must overlap by at least 20 cm in order to ensure continuous injection of the joint.

All changes in direction must be implemented with a sufficiently wide bending radius in order not to damage the hose/restrict the overall injection flow.
The minimum radius is 5 cm.
The injection and ventilation ends can be kept in storage boxes, or alternatively the hose end can be attached to the formwork itself using fastening packers. The storage boxes or fastening packers must be arranged so they are easily accessible in the event of subsequent injection procedures (take high floor structures into consideration).
Once the concrete has cured, the resin can be injected via the fastening packers or the injection end pieces.

Status: 23.03.2022

Prenos navodila za namestitev

Datoteke CAD