Διάσταση Ø περίπου 5/10 mm
αριθμός άρθρου 030050
MASTERTUBE Συστήματα σωλήνων έγχυσης
Η σφράγιση των αρμών κατασκευής σκυροδέματος θέτει υψηλές απαιτήσεις στην τεχνολογία σφράγισης.
Ο σωλήνας έγχυσης MASTERTUBE εξασφαλίζει την αξιόπιστη και μόνιμη στεγανοποίηση οριζόντιων και κατακόρυφων αρμών κατασκευών από σκυρόδεμα έναντι νερού υπό πίεση και χωρίς πίεση. Προσθήκη στη λίστα ειδοποιήσεωνΟι πιο σημαντικές πληροφορίες με μια ματιά
Εσωτερικός σωλήνας PVC
Μανδύας ως ύφασμα μονοκλωστής
περίπου 10 mm
περίπου 5 mm
Ανάλαμψη, με λειτουργία βαλβίδας
depending on injection agent,
approx. + 6°C to +40°C
Πιστοποιητικό δοκιμής της γενικής οικοδομικής αρχής (AbP)
MFPA Λειψίας
Αριθμός: P-SAC 02 / 5.1 / 21 - 266-1 (ρητίνη PU)
Αριθμός: P-SAC 02 / 5.1 / 21 - 266-2 (ακρυλικό)
Μέχρι 2 bar ( 20 m στήλη νερού )
Ja
Κατηγορία χρήσης A για κατηγορίες φορτίου 1 και 2 σύμφωνα με την οδηγία WU
1 ρόλος στα 100 μέτρα
.
![](/Einbauanleitungen/WG3/MASTERTUBE/20284/image-thumb__20284__textandimagecombi/Verpressschlauch_1.caebc070.jpg.pagespeed.ce._U7nsWBh5_.jpg)
The product is supplied on a 100 m reel.
Bind the hose with filament tape and use a suitably sharp tool to cut the hose to the required length.
Injection circuits must not exceed 8 m in length.
![](/Einbauanleitungen/WG3/MASTERTUBE/20286/image-thumb__20286__textandimagecombi/Verpressschlauch_2.af51dbbb.jpg.pagespeed.ce.jlKCLec5Wr.jpg)
After the hose has been cut to length, screw the respective connecting pieces fully into the hose (as far as they will go) - the image shows our fastening packers.
![](/Einbauanleitungen/WG3/MASTERTUBE/20285/image-thumb__20285__textandimagecombi/Verpressschlauch_3.1eceb5e8.jpg.pagespeed.ce.-2R0_Lpkcx.jpg)
Place the hose centrally in the construction joint, within the reinforcement.
The surface of the construction joint must be clean, level and free of burrs, defects and loose particles of dirt.
![](/Einbauanleitungen/WG3/MASTERTUBE/20287/image-thumb__20287__textandimagecombi/Verpressschlauch_4.c7298ddf.jpg.pagespeed.ce._TbLrKs0HH.jpg)
The hose can be fastened in place with metal clips for nailing (manual or nail gun).
The distance between the fastening clips must not exceed 15 cm.
![](/Einbauanleitungen/WG3/MASTERTUBE/20283/image-thumb__20283__textandimagecombi/Verpressschlauch_5.b7139c93.jpg.pagespeed.ce.-g_skGq3yv.jpg)
Alternatively, the hose can be fastened in place with plastic clips, either set in the fresh concrete or subsequently hammered into an 8 mm drill hole.
The distance between the fastening clips must not exceed 15 cm.
The hose must be in continuous contact with the concrete and must not be allowed to float.
![](/Einbauanleitungen/WG3/MASTERTUBE/54453/image-thumb__54453__textandimagecombi/2022-07-29_MASTERTUBE_Fuge_rau.ea3b6fc5.png.pagespeed.ce.WU9OBnBPyn.png)
Fixing on joints with category "rough"
On construction joints with a rough surface, fastening with a fastening grid is necessary to ensure full-surface support on the construction joint. The fixing grid is placed over the hose and fixed alternately (to the left and right of the hose) with nail plugs every 15 cm maximum.
![](/Einbauanleitungen/WG3/MASTERTUBE/20282/image-thumb__20282__textandimagecombi/Verpressschlauch_6.8f177e41.jpg.pagespeed.ce.pLgJpB0AwY.jpg)
Successive injection hose sections must overlap by at least 20 cm in order to ensure continuous injection of the joint.
![](/Einbauanleitungen/WG3/MASTERTUBE/20281/image-thumb__20281__textandimagecombi/Verpressschlauch_7.bdc674fc.jpg.pagespeed.ce.IMQnkCw58u.jpg)
All changes in direction must be implemented with a sufficiently wide bending radius in order not to damage the hose/restrict the overall injection flow.
The minimum radius is 5 cm.
The injection and ventilation ends can be kept in storage boxes, or alternatively the hose end can be attached to the formwork itself using fastening packers. The storage boxes or fastening packers must be arranged so they are easily accessible in the event of subsequent injection procedures (take high floor structures into consideration).
Once the concrete has cured, the resin can be injected via the fastening packers or the injection end pieces.
Status: 23.03.2022
Αξεσουάρ
κατάλληλα αξεσουάρ
Το πακέτο στερέωσης MASTERTEC επιτρέπει τη στερέωση του σωλήνα έγχυσης απευθείας στον ξυλότυπο. Ο συσκευαστής στερέωσης επιτρέπει...
Κλιπ στερέωσης για την ανυψωτική τοποθέτηση σωλήνων έγχυσης σε επιφάνειες από σκυρόδεμα ...
Ρητίνη πολυουρεθάνης για έγχυση σε σωλήνες και ρωγμές ...
Παρόμοια προϊόντα
Μπορείτε να βρείτε παρόμοια προϊόντα εδώ.
Η σφράγιση των αρμών κατασκευής σκυροδέματος θέτει υψηλές απαιτήσεις στην τεχνολογία σφράγισης.Το MASTERTUBE "YELLOW" διασ...
Επικοινωνήστε μαζί μας
Θα χαρούμε να απαντήσουμε στις ερωτήσεις σας