MASTERTUBE iesmidzināšanas šļūtene (sarkana/dzeltena)

MASTERTUBE iesmidzināšanas šļūtene (sarkana/dzeltena)
Izmērs Ø aptuveni 5/10 mm

raksta numurs 030050

MASTERTUBE Iesmidzināšanas šļūteņu sistēmas

Betona konstrukciju šuvju blīvēšanai ir augstas prasības blīvēšanas tehnoloģijai.

MASTERTUBE injekcijas šļūtene nodrošina, ka horizontālās un vertikālās betona konstrukciju šuves var droši un pastāvīgi hermetizēt pret ūdeni zem spiediena un bez spiediena. Pievienot paziņojumu sarakstam

Svarīgākā informācija īsumā

Tehniskie dati

raksta numurs:

030050

rakstu grupa:

300 - Injektionsschlauch

GTIN:

4251689514203

muitas tarifa numurs:

39172190

iepakošanas vienība:

Rullītis

pārdošanas daudzums vienība:

100 m

svars uz:

Rullītis = 10 kg

materiāls:

PVC iekšējā caurule
Apvalks kā monopavediens

krāsa:

rot / gelb

Ārējais diametrs:

apmēram 10 mm

Iekšējais diametrs:

apmēram 5 mm

Izejas atveres:

Slit, ar vārsta funkciju

Lietošanas temperatūra:

depending on injection agent,
approx. + 6°C to +40°C

Testa sertifikāts / atļaujas:

Vispārējā būvvaldes testa sertifikāts (AbP)
MFPA Leipciga
Nr.: P-SAC 02 / 5.1 / 21 - 266-1 (PU sveķi)
Nr.: P-SAC 02 / 5.1 / 21 - 266-2 (akrilāts)

Ūdens spiediena hermētiskums:

Maks. līdz 2 bāriem (20 m ūdens kolonnā)

Piemērotas ūdens maiņas zonas:

Atbilst:

Izmantojiet A klasi 1. un 2. slodzes klasei saskaņā ar WU vadlīnijām

Iepakojums:

1 Rolle 100 m

glabāšana:

Uzglabāt nebojātā un neatvērtā oriģinālajā iepakojumā sausā vietā, prom no tiešiem saules stariem.

izmešana:

Var apglabāt sadzīves atkritumu apglabāšanas vietās saskaņā ar vietējiem atkritumu apglabāšanas noteikumiem.

Datu lapa

Uzstādīšanas pamācība

The product is supplied on a 100 m reel.
Bind the hose with filament tape and use a suitably sharp tool to cut the hose to the required length.
Injection circuits must not exceed 8 m in length.

After the hose has been cut to length, screw the respective connecting pieces fully into the hose (as far as they will go) - the image shows our fastening packers.

Place the hose centrally in the construction joint, within the reinforcement.
The surface of the construction joint must be clean, level and free of burrs, defects and loose particles of dirt.

The hose can be fastened in place with metal clips for nailing (manual or nail gun).
The distance between the fastening clips must not exceed 15 cm.

Alternatively, the hose can be fastened in place with plastic clips, either set in the fresh concrete or subsequently hammered into an 8 mm drill hole.
The distance between the fastening clips must not exceed 15 cm.
The hose must be in continuous contact with the concrete and must not be allowed to float.

Fixing on joints with category "rough"

On construction joints with a rough surface, fastening with a fastening grid is necessary to ensure full-surface support on the construction joint. The fixing grid is placed over the hose and fixed alternately (to the left and right of the hose) with nail plugs every 15 cm maximum.

Successive injection hose sections must overlap by at least 20 cm in order to ensure continuous injection of the joint.

All changes in direction must be implemented with a sufficiently wide bending radius in order not to damage the hose/restrict the overall injection flow.
The minimum radius is 5 cm.
The injection and ventilation ends can be kept in storage boxes, or alternatively the hose end can be attached to the formwork itself using fastening packers. The storage boxes or fastening packers must be arranged so they are easily accessible in the event of subsequent injection procedures (take high floor structures into consideration).
Once the concrete has cured, the resin can be injected via the fastening packers or the injection end pieces.

Status: 23.03.2022

Lejupielādēt instalēšanas pamācību

CAD faili