pro tlakové vodotěsné lepení
číslo článku 040100
Bezrozpouštědlové lepidlo na beton na bázi epoxidové pryskyřice
.PROTECT BK je bezrozpouštědlové lepidlo na beton pro vodonepropustné lepení - FC hmoždinky v tloušťkách stěn FC - a pro silové lepení betonových dílců.
Přidat do seznamu oznámeníPřehled nejdůležitějších informací
Epoxidharz
pasty
Hustota: cca 1,90 g/cm³
přibližně 1,9 kg/m²/mm tloušťky vrstvy
+ 10 °C up to + 30 °C
Termperature of element minimum + 3 °C over dew point
Doba zpracování ( při relativní vlhkosti 50 % )
20 - 30 minut ( 30 °C )
40 - 60 minut ( 20 °C )
90 - 120 minut ( 10 °C )
Vytvrzování ( plná mechanická zatížitelnost )
( při 50 % rel. LF )
3 dny ( 30 °C )
UB 5.1/13-568
7 barů (70 m vodního sloupce)
1 kg kompozitní plechovka
Složka A 0,5 kg
Složka B 0,5 kg
1 : 1 (hmotnostně)
Beton, vodotěsný beton
Minimální stáří 18 dní
Suché, neklouzavé, bezprašné
bez separačních látek, jako je tuk, olej apod.
Mořská a odpadní voda
louhy
Zředěné kyseliny
Minerální oleje
Maziva a pohonné hmoty
Různá rozpouštědla
Další odolnosti na vyžádání nebo prostřednictvím
našeho seznamu odolností
cca 75 - 80 N/mm² (podmínka 100% smáčení)
přibližně 30 N/mm² (podmínkou je 100% smáčení)
nejlépe do 12 měsíců od výroby
Processing/ Mixing:
Allow the hardener component ( component B ) to flow completely into the master component (component A ). Mix intensively with a slowly rotating stirrer (recommendation: double stirrer with counter-rotating stirrer shafts).
Repot into another receptacle and mix thoroughly again.
The compound must be homogeneous, streak-free before application.
Sealing of fibre cement distance tubes with fibre cement plugs:
After cleaning the inside of the fibre cement distance tubes and removing the loose material, the fibre cement plug is dipped into the PROTECT BK and inserted into the distance tube.
The quantity of PROTECT BK on the plug must be sufficient to ensure that the fibre cement plug is fully glued to the inside of the distance tube over its full length.
Depending on the requirements of the construction site, several fibre cement plugs may have to be installed.
Bonding of concrete components:
Depending on the application, PROTECT BK is evenly applied to the components to be bonded using a spatula, smoothing trowel, toothed trowel or similar.
Make sure that the entire surface is bonded without voids.
Immediately after applying the adhesive, the surfaces to be bonded are pressed together and weighted if necessary. For vertical or overhead bonding, the components must be fixed for at least 12 hours,
depending on temperature and layer thickness.
PROTECT BK can be applied in layer thicknesses of 1 - 20 mm.
Please note:
The relative humidity must not exceed 80 %.
Ensure good ventilation after application and during hardening.
Depending on the substance, concentration and duration of exposure, exposure to chemicals can lead to colour changes on the surface which, however, do not affect functionality.
When exposed to UV rays, epoxy resins generally show a certain colour change and chalking.
Status: 23.03.2022
Podobné produkty
Podobné produkty najdete zde.
Vnitřní hydroizolace pro tloušťky stěn z plastů a vláknocementu ...
Vnitřní hydroizolace pro tloušťky stěn z plastů a vláknocementu ...
Vnitřní hydroizolace pro tloušťky stěn z plastů a vláknocementu ...
Kontaktujte nás
Rádi zodpovíme vaše dotazy