na tlakové vodotesné lepenie
číslo článku 040100
Bezrozpúšťadlové lepidlo na betón na báze epoxidovej živice
.PROTECT BK je bezrozpúšťadlové lepidlo na betón na vodonepriepustné lepenie - FC zátky v hrúbkach stien FC - a na silové lepenie betónových dielcov.
Pridať do zoznamu upozorneníNajdôležitejšie informácie na prvý pohľad
Epoxidharz
pasty
Hustota: približne 1,90 g/cm³
cca 1,9 kg/m²/mm hrúbky vrstvy
+ 10 °C up to + 30 °C
Termperature of element minimum + 3 °C over dew point
Čas spracovania (pri relatívnej vlhkosti 50 %)
20 - 30 minút ( 30 °C )
40 - 60 minút ( 20 °C )
90 - 120 minút ( 10 °C )
Vytvrdzovanie ( plná mechanická zaťažiteľnosť )
( pri 50 % rel. LF )
3 dni ( 30 °C )
UB 5.1/13-568
7 barov (70 m vodného stĺpca)
1 kg kompozitná plechovka
Komponent A 0,5 kg
Komponent B 0,5 kg
1 : 1 ( podľa hmotnosti )
Betón, vodotesný betón
Minimálny vek 18 dní
Suché, protišmykové, bezprašné
bez separačných látok, ako je tuk, olej atď.
Morská a odpadová voda
alkálií
Zriedené kyseliny
Minerálne oleje
Mazivá a palivá
Rôzne rozpúšťadlá
Ďalšie odolnosti na požiadanie alebo prostredníctvom
nášho zoznamu odolností
cca 75 - 80 N/mm² (podmienka 100 % zmáčania)
cca 30 N/mm² (podmienka 100 % zmáčania)
najlepšie do 12 mesiacov od výroby
Processing/ Mixing:
Allow the hardener component ( component B ) to flow completely into the master component (component A ). Mix intensively with a slowly rotating stirrer (recommendation: double stirrer with counter-rotating stirrer shafts).
Repot into another receptacle and mix thoroughly again.
The compound must be homogeneous, streak-free before application.
Sealing of fibre cement distance tubes with fibre cement plugs:
After cleaning the inside of the fibre cement distance tubes and removing the loose material, the fibre cement plug is dipped into the PROTECT BK and inserted into the distance tube.
The quantity of PROTECT BK on the plug must be sufficient to ensure that the fibre cement plug is fully glued to the inside of the distance tube over its full length.
Depending on the requirements of the construction site, several fibre cement plugs may have to be installed.
Bonding of concrete components:
Depending on the application, PROTECT BK is evenly applied to the components to be bonded using a spatula, smoothing trowel, toothed trowel or similar.
Make sure that the entire surface is bonded without voids.
Immediately after applying the adhesive, the surfaces to be bonded are pressed together and weighted if necessary. For vertical or overhead bonding, the components must be fixed for at least 12 hours,
depending on temperature and layer thickness.
PROTECT BK can be applied in layer thicknesses of 1 - 20 mm.
Please note:
The relative humidity must not exceed 80 %.
Ensure good ventilation after application and during hardening.
Depending on the substance, concentration and duration of exposure, exposure to chemicals can lead to colour changes on the surface which, however, do not affect functionality.
When exposed to UV rays, epoxy resins generally show a certain colour change and chalking.
Status: 23.03.2022
Podobné produkty
Podobné produkty nájdete tu.
Vnútorná hydroizolácia pre hrúbky stien z plastu a vláknocementu ...
Vnútorná hydroizolácia pre hrúbky stien z plastu a vláknocementu ...
Vnútorná hydroizolácia pre hrúbky stien z plastu a vláknocementu ...
Kontaktujte nás
Radi vám odpovieme na vaše otázky