för trycksatt vattentät limning
artikelnummer 040100
Lösningsmedelsfritt betonglim baserat på epoxiharts
.PROTECT BK är ett lösningsmedelsfritt betonglim för vattengenomsläpplig limning - FC-pluggar i FC-väggtjocklekar - och för formpressad limning av betongdelar.
Lägg till i meddelandelistanDen viktigaste informationen i en överblick
Epoxidharz
pastasmakande
Densitet: ca 1,90 g/cm³
ca. 1,9 kg/m²/mm skikttjocklek
+ 10 °C up to + 30 °C
Termperature of element minimum + 3 °C over dew point
Bearbetningstid (vid 50 % relativ luftfuktighet)
20 minuter
20 - 30 minuter (30 °C)
40 - 60 minuter ( 20 °C )
90 - 120 minuter ( 10 °C )
90 - 120 minuter ( 10 °C )
Härdning ( full mekanisk belastningskapacitet )
( vid 50 % rel. LF )
3 dagar ( 30 °C )
UB 5.1/13-568
.
7 bar (70 m vattenpelare)
1 kg kompositburk
Komponent A 0,5 kg
.
Komponent B 0,5 kg
1 : 1 (efter vikt)
Betong, vattentät betong
.
Minimiålder 18 dagar
Torr, halksäker, dammfri
fri från avskiljande ämnen som fett, olja etc.
Sjövatten och avloppsvatten
.
alkalier
.
Utspädda syror
Mineraloljor
Smörjmedel och bränslen
Olika lösningsmedel
.
Ytterligare resistenser på begäran eller via
vår beständighetslista
ca 75 - 80 N/mm² (förutsätter 100% vätning)
ca. 30 N/mm² (förutsättning 100% vätning)
bäst före 12 månader efter produktion
Processing/ Mixing:
Allow the hardener component ( component B ) to flow completely into the master component (component A ). Mix intensively with a slowly rotating stirrer (recommendation: double stirrer with counter-rotating stirrer shafts).
Repot into another receptacle and mix thoroughly again.
The compound must be homogeneous, streak-free before application.
Sealing of fibre cement distance tubes with fibre cement plugs:
After cleaning the inside of the fibre cement distance tubes and removing the loose material, the fibre cement plug is dipped into the PROTECT BK and inserted into the distance tube.
The quantity of PROTECT BK on the plug must be sufficient to ensure that the fibre cement plug is fully glued to the inside of the distance tube over its full length.
Depending on the requirements of the construction site, several fibre cement plugs may have to be installed.
Bonding of concrete components:
Depending on the application, PROTECT BK is evenly applied to the components to be bonded using a spatula, smoothing trowel, toothed trowel or similar.
Make sure that the entire surface is bonded without voids.
Immediately after applying the adhesive, the surfaces to be bonded are pressed together and weighted if necessary. For vertical or overhead bonding, the components must be fixed for at least 12 hours,
depending on temperature and layer thickness.
PROTECT BK can be applied in layer thicknesses of 1 - 20 mm.
Please note:
The relative humidity must not exceed 80 %.
Ensure good ventilation after application and during hardening.
Depending on the substance, concentration and duration of exposure, exposure to chemicals can lead to colour changes on the surface which, however, do not affect functionality.
When exposed to UV rays, epoxy resins generally show a certain colour change and chalking.
Status: 23.03.2022
Liknande produkter
Du hittar liknande produkter här.
Invändigt tätskikt för väggtjocklekar av plast och fibercement ...
Invändigt tätskikt för väggtjocklekar av plast och fibercement ...
Invändigt tätskikt för väggtjocklekar av plast och fibercement ...
Kontakta oss
Vi svarar gärna på dina frågor