Πλήρης επικάλυψη και στις δύο πλευρές με βάση
αριθμός άρθρου 070468
Η σφράγιση των αρμών κατασκευής σκυροδέματος θέτει υψηλές απαιτήσεις στην τεχνολογία σφράγισης.
Τα πλήρως επικαλυμμένα φύλλα στεγανοποίησης Rolle-F φύλλο στεγανοποίησης με βάση εξασφαλίζουν ότι οι αρμοί κατασκευής σκυροδέματος στεγανοποιούνται με ασφάλεια και μόνιμα έναντι πιεστικού και μη πιεστικού νερού.
Οι πιο σημαντικές πληροφορίες με μια ματιά
St 37, γαλβανισμένο
Ειδική επίστρωση: πολυμερές πλαστικό ενισχυμένο με ύφασμα
20,00 m
160 mm
Περίπου 0,6 mm
Περίπου 0,15 mm
Περίπου 0,9 mm
Πιστοποιητικό δοκιμής γενικής οικοδομικής αρχής (AbP)
MFPA Leipzig
ja
Κατηγορία χρήσης A για κατηγορίες φορτίου 1 και 2 σύμφωνα με την οδηγία WU
Όχι
Ja
Χαρτόνι (40 x 40 x 20 cm)
1 ρολό
2 βραχίονες στερέωσης
36 κουτιά ανά παλέτα
Δοκιμή τεχνικής εφαρμογής έως 8 bar
![](/Einbauanleitungen/WG2/Dichtblech%20Rolle%20F/39401/image-thumb__39401__textandimagecombi/_DSC3484.efbf6d01.png)
Packaging
1 Role with 20 m
2 fixing clips
![](/Einbauanleitungen/WG2/Dichtblech%20Rolle%20F/39402/image-thumb__39402__textandimagecombi/_DSC3570.ef937132.png)
Remove the bottom half of the parted protective foil from the special coating.
![](/Einbauanleitungen/WG2/Dichtblech%20Rolle%20F/39403/image-thumb__39403__textandimagecombi/_DSC3587.54576d01.png)
Place the Joint Sheet Metal Role-F on the top reinforcement in the center of the rising wall. Use binding wire to tie the fastening foot to the reinforced layer. The emedment depth in the concrete must be at least 3 cm and must not exceed half of the sheet height (8 cm).
![](/Einbauanleitungen/WG2/Dichtblech%20Rolle%20F/39400/image-thumb__39400__textandimagecombi/Einbauanleitung,P20Pimcore.2ca7f97b.jpg.pagespeed.ce.xsSj7xFDGo.jpg)
By bending and crimping a festenig foot to the opposite side (approx. every 50 cm) the position of the sheet can be addtionally stabilized.
![](/Einbauanleitungen/WG2/Dichtblech%20Rolle%20F/39404/image-thumb__39404__textandimagecombi/_DSC3525.b93830e4.png)
In the corner area, the sheet is bent according to the course of the corner. It is advisable here to bend over a "sharp" edge.
![](/Einbauanleitungen/WG2/Dichtblech%20Rolle%20F/39405/image-thumb__39405__textandimagecombi/_DSC3551.3f2fab3c.png)
At transition joints, the Joint Sheet Metal Role-F must be overlapped by at least 6cm. For this purpose, the protective film is folded badk along the length of the overlap.
![](/Einbauanleitungen/WG2/Dichtblech%20Rolle%20F/39407/image-thumb__39407__textandimagecombi/_DSC3559.e0869bb8.png)
The overlapping surfaces are pressed together over the entire surface and secured with one of the supplied fixing clips. Ther must be no dirt on the adhesie surfaces that could impair the bonding.
![](/Einbauanleitungen/WG2/Dichtblech%20Rolle%20F/39408/image-thumb__39408__textandimagecombi/_DSC3573.f5691fdf.png)
The Joint Sheet Metal Role-F must form a self-contained, defect-free circuit. The upper half of the protective film must remain on the special coating until the latest possible time. The concreting of the wall base and the corresponding preparations for this must be carried out in accordance with the recognized technical regulations.
Status: 23.03.2022
Επικοινωνήστε μαζί μας
Θα χαρούμε να απαντήσουμε στις ερωτήσεις σας